Pelco Home Security System C494M E User Manual

I N S T A L L A T I O N  
HS2000  
High Security  
Enclosure  
C494M-E (9/06)  
 
Contents  
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Optional Window Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Replacement Tamper Switch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Tamper Switch Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Service Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Exploded Assembly Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
C494M-E (9/06)  
3
 
Important Safety Instructions  
1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.  
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not  
be installed where exposed to rain and moisture.  
3. Only use replacement parts recommended by Pelco.  
4. The camera and lens combination shall not exceed 20 lb (9.06 kg).  
5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, and camera and  
lens combination.  
The product may bear the following marks:  
This symbol indicates that dangerous voltage constituting a risk of  
electric shock is present within this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are important operating and  
maintenance instructions in the literature accompanying this unit.  
4
C494M-E (9/06)  
 
Description  
The HS2000 high-security camera enclosure is designed for indoor corner mount installation in such settings as elevators, parking garages,  
classrooms, offices, and detention cells requiring maximum protection from vandalism in an unobtrusive package. It fits flush to the ceiling in a  
corner. An impact-resistant clear Lexan® polycarbonate resin thermoplastic window is supplied, and an optional smoked window is available.  
Constructed of medium gauge steel, the HS2000 will accept many of the smaller CCD cameras with fixed focal length and auto-iris lenses. There  
is no exposed mounting hardware securing the HS2000 to its mounting surface. Opening the enclosure can only be accomplished by removing  
the tamper-resistant screw from the bottom. For additional security, a factory-installed tamper switch is mounted on the secured access cover.  
OPTIONAL ACCESSORY  
HS200010019  
Smoked window, 0.25" (6.35 mm) thick, impact and abrasion-resistant Lexan polycarbonate resin thermoplastic  
C494M-E (9/06)  
5
 
Installation  
Before installing the HS2000 to a wall, make sure that the mounting surface is able to support four times the full weight of the enclosure,  
camera, and lens.  
The tilt table and tilt table mounting brackets may be removed to provide adequate clearance for mounting the enclosure.  
NOTE: The four fasteners required to secure the HS2000 to a wall (minimum 3/8” diameter recommended) are not supplied.  
To mount the enclosure to a wall (tight to the ceiling), perform the following steps:  
1. Remove the cover from the mounting bracket. A special socket is provided (fits 1/4" square drive).  
2. Using the mounting bracket as a template, mark and drill holes in the mounting surface.  
3. Attach the enclosure with the required fasteners.  
4. Route the required cables through the back or top.  
5. Mount the camera/lens to the tilt table.  
6. Make all appropriate connections: camera power, video [coax], and lens.  
7. Position the camera and tighten the 1/4-20 fasteners to secure the tilt table in place.  
8. Replace the cover and secure with the 1/4-20 tamper-resistant screw that is provided.  
NOTE: A plate is provided to prevent access through the top of this enclosure. If needed, it is mounted with the mounting bracket using the  
same mounting holes and hardware.  
OPTIONAL WINDOW INSTALLATION  
The HS2000 is provided with a clear 0.25" (6.35 mm) thick viewing window. An optional smoked window, HS200010019, is available.  
Instructions for installing the optional smoked window are as follows:  
1. Remove the cover from the mounting bracket. A special socket is provided.  
2. Remove the four 1/4-20 elastic locknuts and 1/4" flat washers.  
3. Remove the window.  
4. Remove the protective coatings from the new window and place the window over the four 1/4-20 studs.  
5. Replace the hardware and replace the cover.  
6
C494M-E (9/06)  
 
REPLACEMENT TAMPER SWITCH INSTALLATION  
The HS2000 enclosure comes with a tamper switch installed. If you need to install a replacement switch, refer to Figure 1 for the correct position  
of the switch and perform the following steps:  
1. Remove the front cover.  
2. Install the switch and secure with lock washers and nuts.  
TAMPER SWITCH WIRING  
The tamper switch comes with normally open and normally closed contacts.  
For a normally open circuit, use the “open” and “common” terminals; for a normally closed circuit, use the “closed” and “common” terminals.  
BRACKET/SWITCH  
MOUNTING PLATE  
Figure 1. HS2000 Series Tamper Switch Installation  
C494M-E (9/06)  
7
 
Maintenance  
Maintenance performed at regularly scheduled intervals will help prolong the operational life and appearance of the equipment.  
Clean the window with a mild nonabrasive detergent in water and a soft cloth regularly to help maintain picture clarity. For a heavily soiled  
window, use vinyl cleaner.  
SERVICE MANUAL  
If you need to repair the camera enclosure, obtain a service manual in one of the following ways:  
Contact Pelco’s Literature Department and request service manual C494SM.  
8
C494M-E (9/06)  
 
Exploded Assembly Diagram  
Figure 2. HS2000 Exploded Assembly Diagram  
Table A. Mechanical Parts List  
Item No.  
Qty Description  
Part Number  
1
1
1
1
1
1
1
1
1
2
1
2
2
4
11  
4
1
2
2
Bracket, switch, break-in  
HS10004313COMP  
MF00-0250-001A  
HS20004001COMP  
HS20004003COMP  
HS20004007COMP  
HS20004023COMP  
HS20004115COMP  
HS20004215COMP  
SWI1DM401  
Window, 8" x 7" x 0.25" drilled MR10 clear Lexan thermoplastic  
Plate, mounting  
Cover, front, beige  
Tilt table  
Cover, top, corner mount  
Bracket, mount, tilt table, left  
Bracket, mount, tilt table, right  
Switch, tamper  
Aꢁ  
Screw, 1/4-20 x 1/2", round, tamper-resistant, #10, stainless steel  
Screw, 1/4-20 x 3/4", round, tamper-resistant, #10, stainless steel  
Bolt, 1/4-20 x 5/8", hex cap head, stainless steel  
Nut, hex, 1/4-20, stainless steel  
ZH1/4-20X.50SRT  
ZH1/4-20X.75SRT  
ZH1/420X.625CH  
ZH1/4-20NUTCH  
ZH1/4LWSSL  
ꢀꢁ  
B
ꢀꢁ  
C
ꢀꢁ  
D
ꢀꢁ  
E
Washer, split lock, 1/4", stainless steel  
Washer, flat, 3/16", special, stainless steel  
Nut, lock, 1/4-20 nylon insert, stainless steel  
Socket, tamper-resistant #10, 1/4" drive (not shown)  
Nut, hex, 6-32, stainless steel  
ꢀꢁ  
F
ZH260X562X65C  
ZH1/420NUTCHN  
ZTSOCKET10  
ꢀꢁ  
G
ꢀꢁ  
H
ꢀꢁ  
I
ZH6-32NUTSH  
ꢀꢁ  
J
Washer, lock, internal tooth, #6, stainless steel  
ZH6LWSIS  
C494M-E (9/06)  
9
 
Specifications  
Mechanical  
Camera Mounting  
Adjustable tilt table  
Maximum Camera/Lens Size  
Accepts camera/lens combinations (including BNC connector) up to  
3.0" H x 3.0" W x 6.0" L (7.62 x 7.62 x 15.24 cm)  
Enclosure Mounting  
Security  
Four 0.390-inch (0.99 cm) diameter holes on protected rear surface  
Tamper-resistant screw; N.O./N.C. switch contact on cover  
Tamper Switch  
Plunger type door switch with “pull to cheat” feature. N.O./N.C. contacts clearly marked on body of  
switch. DM electrical rating: 10 A, 125 VAC.  
Electrical  
Cable Entry  
Access through back and top  
Tamper Switch  
0.250-inch (0.63 cm) quick connect. N.O./N.C. clearly marked on switch body. 10 A maximum switching  
current, 125 VAC maximum switching voltage  
General  
Window  
0.250-inch (6.35 mm) thick impact and abrasion-resistant, clear Lexan polycarbonate resin thermoplastic  
Construction  
Finish  
Formed 14 gauge 0.074-inch (0.19 cm) steel  
Gray polyester powdercoat  
Environment  
Unit Weight  
Indoor; 32° to 120°F (0° to 49°C)  
7.77 lb (3.52 kg)  
(Design and product specifications are subject to change without notice.)  
10.25  
(26.04)  
10.13  
(25.73)  
4.50  
(11.43)  
5.00  
(12.70)  
8.00  
(20.23)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.  
10  
C494M-E (9/06)  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted  
pair transmission products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.  
The lamp and color wheel will be covered for a period of 90 days. The air filter is not  
covered under warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelco’s liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
C494M  
C494M-A  
C494M-B  
C494M-C  
C494M-D  
Date  
5/90  
9/93  
9/95  
11/95  
1/96  
4/96  
9/06  
Comments  
Original version.  
Put into two-column format. Exploded assembly diagram and parts list updated.  
Rev. B. Revised to include wiring instructions for tamper switch and put into new two-column format.  
Rev. C. Revised to include updated tamper switch/bracket part numbers and exploded view diagram.  
Rev. D. Revised to include tamper switch installation, specification description and new part numbers per ECO 95-397.  
Revised Section 7.0, item no. 1 to part number HS10004313COMP.  
C494M-E  
Updated to new format. Revised per ECO 05-13392. Removed obsolete models. Updated parts list per ECO 06-14885 and 06-13896.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2006, Pelco. All rights reserved.  
DLP is a registered trademark of Texas Instruments, Inc.  
Lexan is a registered trademark of the General Electric Company.  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Australia Canada Finland France Italy Russia Singapore Spain Sweden The Netherlands United Arab Emirates United Kingdom United States  
|
|
|
|
|
|
|
|
|
|
|
|
 

Peavey Speaker System 12 D User Manual
Peerless Industries TV Video Accessories FLD UNV User Manual
Pelco Stereo System RM2196 User Manual
Philips CD Player CDR 600 17 User Manual
Philips Computer Monitor MML1801 User Manual
Philips Projection Television 9P5531C User Manual
Pioneer MP3 Player SEP C1 User Manual
Planar Computer Monitor PT1503NT User Manual
Polaris Offroad Vehicle RZR 4 User Manual
ProForm Treadmill PFTL79101 User Manual