Pelco Home Security System C497M D 1 96 User Manual

®
HS4000  
High-Security Enclosure  
Installation/Operation Manual  
C497M-D (1/96)  
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827  
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120  
 
INSTALLATION/OPERATION MANUAL  
HS4000 HIGH-SECURITY ENCLOSURE  
1.0 WARNINGS  
Priortoinstallationanduseofthisproduct,thefollowing  
WARNINGS should be observed.  
4. After replacement/repair of this unit’s electrical  
components, conduct a resistance measurement  
betweenlineandexposedpartstoverifytheexposed  
parts have not been connected to line circuitry.  
1. Installation and servicing should only be done by  
Qualified Service Personnel and conform to all  
Local codes.  
5. The installation method and materials should be  
capable of supporting four (4) times the weight of  
theenclosure,pan/tilt,cameraandlenscombination.  
2. Unless the unit is specifically marked as a NEMA  
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is  
designed for indoor use only and it must not be  
installed where exposed to rain and moisture.  
3. Only use replacement parts recommended by  
PELCO.  
The product may bear the following  
marks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
within this unit.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
CAUTION:  
TOREDUCETHERISKOFELECTRICAL  
SHOCK, DO NOT REMOVE COVER. NO  
USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
Please thoroughly familiarize yourself with the information in this manual  
prior to installation and operation.  
Pelco Manual C497M-D (1/96)  
1
 
2.0 SCOPE  
This enclosure has a removable rear cap for easy ac-  
cess to the slide-out platform on which the camera is  
mounted. The removable front cap allows manual lens  
adjustments to be made without removing the camera.  
Access to the interior can only be gained with a spe-  
cially designed tool, eliminating the possibility of the  
enclosure being opened by unauthorized personnel.  
The information contained within this manual covers  
the HS4000 High Security Camera Enclosure.  
2.1 DESCRIPTION  
The HS4000 is a high-security camera enclosure de-  
signed for use with 2/3-inch cameras and will accom-  
modate fixed focal length lenses or motorized zoom  
lenses with or without auto-iris operation.  
A factory-installed tamper switch provides additional  
security.  
The HS4000 has been engineered for indoor use as a  
stand-alone enclosure in prisons, detention cells, or  
other applications requiring maximum protection from  
vandalism.  
Figure 1. HS4000 Dimension Drawing  
2
Pelco Manual C497M-D (1/96)  
 
3.0 INSTALLATION  
3.1 CAMERA/LENS INSTALLATION  
The following hardware is supplied with the enclosure  
and can be used to mount the enclosure or the camera/  
lens:  
1. Remove the four (4) “tampruf” screws from the  
rear cap with the tool provided.  
2. Remove the rear cap from the enclosure. Loosen  
the bolt on the camera sled assembly and remove  
it from the rail.  
Quantity  
Item  
2
4
4
2
1/4-20 x .500 hex head screws  
1/4 flat washers  
1/4 split washers  
3. Place the camera/lens on the sled assembly.  
1/4-20 “tampruf” screws  
NOTE: Position the camera/lens at the  
forward-most point on the sled, while al-  
lowing clearance between the lens and en-  
closure window when the lens is adjusted  
to its maximum physical length.  
4. Secure the camera/lens to the sled with the 1/4-20  
hex head screws provided.  
5. Pull the video and power cables through the knock-  
outs and attach to the camera.  
6. Adjust camera focus and iris if necessary.  
7. Replace the sled onto the rail and slide the assem-  
bly into the enclosure; replace the bolt and secure.  
8. Replace the rear cap and the four (4) “tampruf”  
screws.  
9. Attach the enclosure to the appropriate mount or  
pan/tilt using the instructions provided.  
NOTE: If the lens needs to be adjusted fur-  
ther after installation has been completed, it is  
easier to remove the front cap to make final lens  
adjustments.  
Pelco Manual C497M-D (1/96)  
3
 
4.0 TAMPER SWITCH INSTALLATION  
6.0 SPECIFICATIONS  
MECHANICAL  
The HS4000 High-Security enclosures come standard  
from the factory with a tamper switch(es) mounted on  
the secured access door. Refer to Section 4.1 for wir-  
ing.  
Camera  
Mounting:  
Viewing  
Multiple holes on camera sled  
Window:  
1/2" (1.27 cm) thick impact and abra-  
sion resistant Lexan  
Should it become necessary to install a replacement  
switch, reference Figure 2 and perform the following  
steps:  
Camera Size:  
Accommodates camera/lens combi-  
nations up to:  
6.00" W x 4.75" H x 15.00" L  
(15.24 cm x 12.07 cm x 38.10 cm)  
Tamper Switch: Plunger type door switch with “pull  
to cheat” feature. N.O/N.C. contacts  
1. Open the enclosure by removing the end plate from  
the desired “alarmed” opening.  
clearly marked on body of switch.  
DM electrical rating: 10A, 125V.  
2. Install the bracket so that the mounting studs go  
through the slots in the bracket.  
Security:  
Tamper-resistant screws N.O./N.C.  
switch contact on secure cover  
NOTE: The slot in the bracket allows the switch  
to be used against either the 1/2" (1.27 cm) thick  
lexan window or the .134" (0.34 cm) thick metal  
plate.  
ELECTRICAL  
Cable Entry:  
Two (2) cable knockout holes on rear  
plate  
Tamper Switch: 1/4" (.63 cm) quick connect. N.O./  
N.C. clearly marked on switch body.  
3. If the switch is to be used against the metal plate,  
slide the bracket so that the studs are at the end of  
the slot that is furthest from the switch plunger.  
10A, maximum switching current  
125V, maximum switching voltage.  
4. If the switch is to be used against the Lexan win-  
dow, slide the bracket so that the studs are at the  
end of the slot nearest the switch plunger.  
GENERAL  
Construction:  
Seam welded 10 gauge .134" (0.34  
cm) steel  
Finish:  
Dimensions:  
Weight:  
Poly vinyl powder coat  
See Figure 1  
22 lbs (9.9 kg)  
5. When reinstalling the front/rear plate, position the  
plate flush with the end of the enclosure body.  
4.1 WIRING THE SWITCH  
(Product specifications subject to change  
without notice.)  
The tamper switch comes with both a “Normally Open”  
contact and a “Normally Closed” contact.  
For a “Normally Open” circuit, use the “open” and  
“common” terminals.  
For a “Normally Closed” circuit, use the “closed”  
and “common” terminals.  
5.0 CARE AND MAINTENANCE  
Regularly scheduled maintenance will help prolong the  
appearance of the equipment.  
Clean the window regularly with a soft cloth and mild  
nonabrasive detergent in water to help maintain picture  
clarity.  
Figure 2. HS4000 Series Tamper Switch Installation  
4
Pelco Manual C497M-D (1/96)  
 
7.0 EXPLODED ASSEMBLY DIAGRAM  
Figure 3. HS4000 Exploded Assembly Diagram  
7.1 MECHANICAL PARTS LIST  
Item  
Quantity  
Description  
Part Number  
1
2
3
4
5
6
7
8
9
1
1
2
1
1
2
2
10  
1
Lexan window  
Body assembly  
Front/rear plate  
Sled  
Knockouts plate  
Tamper switch bracket  
Tamper switch  
Screws, “tampruf” #10, SS, 1/4-20 x 1/2" round  
Socket, “tampruf” #10  
AH80001001  
HS40001100WA  
HS40004003COMP  
EH40144001COMP  
HS40004015COMP  
HS30004113COMP  
SWI1DM401  
ZH1/4-20X.50SRT  
ZTSOCKET10  
A
B
C
D
E
F
4
16  
1
4
4
1/4-20 Nut-lock  
1/4" Flat washer  
1/4-20 x 1.25" Screw  
1/4" Split lock washer  
1/4-20 Hex nut  
ZH1/420NUTCHN  
ZH260X562X65C  
ZH1/420X1.25CS  
ZH1/4LWSSL  
ZH1/4-20 NUTCH  
ZH6LWSIS  
4
4
#6 Lock washer  
6-32 Hex nut  
G
ZH6-32NUTSH  
Pelco Manual C497M-D (1/96)  
5
 
8.0 WARRANTY AND RETURN  
INFORMATION  
WARRANTY  
RETURNS  
Pelco will repair or replace, without charge, any merchandise proved  
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate  
of shipment.  
In order to expedite parts returned to the factory for repair or credit, please  
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an  
authorization number (CA number if returned for credit, and RA number  
if returned for repair).  
Exceptions to this warranty are as noted below:  
All merchandise returned for credit may be subject to a 20% restocking  
and refurbishing charge.  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and  
keyboard).  
Three years on Camclosure® and fixed camera models, except the  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,  
and MC3651H-2X camera models, which have a five-year warranty.  
Goods returned for repair or credit should be clearly identified with the  
assigned CA or RA number and freight should be prepaid. Ship to the  
appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto  
Rico, send goods to:  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and  
DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, includ-  
ing when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding  
wiper blades).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto  
Rico and are instructed to return goods to the USA, you may do one of the  
following:  
Eighteen months on DX Series digital video recorders, NVR300  
Series network video recorders, and EnduraSeries distributed  
network-based video products.  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
One year (except video heads) on video cassette recorders (VCRs).  
Video heads will be covered for a period of six months.  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods  
to:  
Six months on all pan and tilts, scanners or preset lenses used in  
continuousmotionapplications(thatis,presetscan,tourandautoscan  
modes).  
Pelco c/o Expeditors  
473 Eccles Avenue  
Pelco will warrant all replacement parts and repairs for 90 days from the  
date of Pelco shipment. All goods requiring warranty repair shall be sent  
freight prepaid to Pelco, Clovis, California. Repairs made necessary by  
reason of misuse, alteration, normal wear, or accident are not covered  
under this warranty.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco assumes no risk and shall be subject to no liability for damages or  
loss resulting from the specific use or application made of the Products.  
Pelco’s liability for any claim, whether based on breach of contract,  
negligence, infringement of any rights of any party or product liability,  
relating to the Products shall not exceed the price paid by the Dealer to  
Pelco for such Products. In no event will Pelco be liable for any special,  
incidental or consequential damages (including loss of use, loss of profit  
and claims of third parties) however caused, whether by the negligence  
of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The  
Dealer may also have additional rights, which are subject to variation from  
state to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800)  
289-9100 or (559) 292-1981 to obtain a Repair Authorization number  
(RA), and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice  
number  
3. Details of the defect or problem If there is a dispute regarding the  
warranty of a product which does not fall under the warranty conditions  
stated above, please include a written explanation with the product  
when returned.  
Method of return shipment shall be the same or equal to the method by  
which the item was received by Pelco.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
6
Pelco Manual C497M-D (1/96)  
 

Pelco Security Camera C416M C User Manual
Philips Computer Monitor HW9190T User Manual
Philips Flat Panel Television 15PF9937 User Manual
Philips Work Light 57903 87 16 User Manual
Philips Work Light EL2 Series User Manual
Pioneer DVD Player DVD 116 User Manual
Poulan Blower 530088073 User Manual
Poulan Lawn Mower 173411 User Manual
Power Acoustik Car Video System PMD 112CMX User Manual
ProForm Home Gym PFEL51053 User Manual