Pelco Security Camera C2506E User Manual

C934M-F (7/99)  
C2506/C2525  
Pre-Wired Interconnecting Cables  
®
3500 Pelco Way,  
Clovis, CA 93612-5699  
USA  
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Installation and servicing should be done by qualified service and installation personnel only.  
In North America & Canada:  
Tel (800) 289-9100  
FAX (800) 289-9150  
2. Installation should be done in accordance with all local and national electrical and mechani-  
cal codes using only approved materials.  
International Customers:  
Tel (1-559) 292-1981  
FAX (1-559) 348-1120  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
within this unit.  
C A U T I O N :  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation and  
operation.  
DESCRIPTION  
The C2506 and C2525 are pre-wired cables used to connect Pelco’s CX9000 Series Coaxitron®  
receiver with Pelco’s SB1900, SB2500, SB2600, and SS2000 Series domes and Legacy® Series  
pan and tilts in indoor applications only. The C2506E and C2525E are used with CX9000 Series  
receivers and Legacy® Series pan and tilts in outdoor applications.  
Models  
C2506  
C2506E  
C2525  
Indoor, 6-foot (1.8 m), pre-wired interconnecting cable (UL)  
Same as C2506 but for outdoors  
Indoor, 25-foot (7.6 m), pre-wired interconnecting cable (UL)  
Same as C2525 but for outdoors  
C2525E  
INSTALLATION  
1. Connect the male 37-pin CPC connector to the Coaxitron® receiver.  
2. Connect the female 37-pin CPC connector to the dome or pan and tilt unit.  
3. Use the controller to perform the following functions (if applicable) and verify each operates  
correctly:  
• Pan left  
• Pan right  
• Tilt down  
• Tilt up  
• Zoom tele  
• Iris open  
• Iris closed  
• Focus near  
• Focus far  
• Preset operation  
• Camera power  
• Enclosure power  
• Camera sync  
• Zoom wide  
Installation is complete when all the above functions operate correctly. If they do not, refer to the  
Troubleshooting section.  
TROUBLESHOOTING  
1. If any of the functions do not operate correctly, check the cable wiring (refer to Figure 1).  
If the pan and tilt functions operate backwards (for example, “tilt up” actually tilts down and  
“pan right” actually pans left), pins 3 and 7 for pan and pins 5 and 6 for tilt are reversed. You  
can correct the problem in the field with a CPC pin/socket extracting tool by exchanging the  
reversed function. If you lack the necessary tool, contact Pelco for a return authorization  
number to exchange the cable.  
2. If the connections are loose, tighten the lock ring on the CPC connectors.  
3. Check the Coaxitron® receiver to determine if it is operating correctly.  
 

Pelco Landscape Lighting C2433SM A 8 02 User Manual
Pentax Binoculars 822 User Manual
Philips Cell Phone CT9A9RSLV User Manual
Philips Digital Photo Frame NBR 220 User Manual
Philips Stereo System DVD580HC User Manual
Philips Trimmer NT9110 User Manual
Pioneer Cassette Player KEH P2033R User Manual
Planar Crib Toy PD7130 User Manual
Planet Technology Switch FGSW 2620 User Manual
Presto Fryer GranPappy User Manual