Polaroid Printer CZA 10011 User Manual

Safety Information  
Hereby, Polaroid Corporation declares that this Instant Mobile Printer is in compliance with the essential  
requirements and other relevant provisions of Directive 1999/5/EC.  
Product Diagram  
Troubleshooting  
AC adapter input  
PROBLEM  
SOLUTION  
Changes or modifications not expressly approved by the party responsible for compliance could void the  
user’s authority to operate the equipment.  
The photo has streaks  
DO NOT:  
DO:  
Send another image to be printed.  
NOTICE  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation.  
Paper  
door latch  
Turn off the printer. Open the paper tray  
door and remove the photo paper. Place  
one sheet of photo paper upside down (with  
the watermark facing up) in the paper tray.  
Gently glide the photo paper under the print  
head. Close the paper tray door. The sheet  
of photo paper will automatically eject.  
Open the paper tray door and reload the  
photo paper.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there  
is no guarantee that interference will not occur in a particular installation. If this equipment does not cause  
harmful interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
Photo  
exit slot  
-
-
-
Reorient or relocate the receiving antenna  
Increase the separation between the equipment and receiver  
Connect the equipment into an outlet or on a circuit different from that to which the receiver  
is connected  
Paper tray door  
The paper jammed before printing  
(nothing has been ejected)  
DO NOT:  
Send another image to be printed.  
-
Consult the dealer or an experienced radio/TV technician for help.  
DO:  
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.  
Open paper tray door.  
This equipment complies with the FCC/IC radiation exposure limits sent forth for uncontrolled equipment and  
meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET62 and RSS-102 for the IC  
radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply  
without maximum permissive exposure evaluation (MPE). But it is desirable that is should be installed and  
operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands,  
wrists, feet, and ankles).  
Check to see if there is paper in the tray.  
If so, ensure the paper is loaded correctly.  
If not, add a new pack of Polaroid ZINK  
Photo Paper.  
Power button Power/Battery  
LED indicator  
Status LED  
indicator  
USB connector Battery cover  
The paper jammed while printing  
(part of the image has already  
ejected)  
DO NOT:  
Pull out paper.  
This device complies with Part 15 of the FCC Rules and the RSS-Gen of IC Rules. Operation is subject to  
the following two conditions: (1) this device may not cause interference, and (2) this device must accept any  
interference, including interference that may cause undesired operation of this device.  
DO:  
Turn off the printer. Open the paper tray door  
and remove media. Place one sheet of photo  
paper upside down (with the watermark  
facing up) in the paper tray. Gently glide the  
photo paper under the print head. Close the  
paper tray door. The sheet of photo paper  
will automatically eject. Open the paper tray  
door and reload the photo paper. Close the  
paper tray door.  
CAUTION  
LED  
Color  
Action  
Communication  
RISK OF EXPLODING IF BATTERY IS REPLACED BY AN INCORRECT TYPE.  
BATTERY CAUTIONS  
1. Use only the provided charger with this product.  
2. Only charge the battery as recommended by the instructions.  
3. The battery provided with his product is intended for this product only.  
4. Prolonged use of the printer will result in the battery becoming warm.  
Green  
Solid  
Solid  
Power on  
Low battery  
Orange  
Red  
Solid  
Out of battery  
Orange  
Green  
Green  
Green  
Green  
Red  
Pulse (1X speed)  
Pulse (1X speed)  
Solid  
Charging from AC adapter  
Fully charged from AC adapter  
Ready to print  
BATTERY WARNINGS  
1. Avoid contact with leaking or a damaged battery.  
2. Do not short battery terminals.  
3. Adult supervision is recommended when product is used by young children.  
4. Avoid areas of excessive heat or moisture.  
5. Do not disassemble the battery.  
If all else fails...  
DO:  
Turn off the printer. If the printer will not  
power off, remove the battery cover and the  
battery. Replace the battery and batter cover.  
Turn on the printer.  
Pulse (1X speed)  
Pulse (3X speed)  
Pulse (1X speed)  
Solid  
Receiving information  
Printing  
This product contains electrical or electronic materials. The presence of these materials  
may, if not disposed of properly, have potential adverse effects on the environment and  
human health. Presence of this label on the product means it should not be disposed of  
as unsorted waste and must be collected separately. As a consumer, you are responsible  
for ensuring that this product is disposed of properly. To find out how to properly  
dispose of this product, please go to www.polaroid.com and click on “Company“  
or call the customer service number for your country listed in the instruction manual.  
For additional troubleshooting and frequently asked questions,  
Paper jam  
Orange  
Out of paper, non feed  
Printing: Camera Cell Phone  
Installing and Charging the Battery  
Passcode: 6-0-0-0  
To install the battery:  
1
2
3
The following is an example for connecting to the printer and print your images. The  
terminology used in your cell phone may be different.  
1. Select the image you would like to print from the stored images  
on your camera cell phone. In the “options” menu, select “send  
via Bluetooth.” Search for devices and select the Polaroid printer  
and print.  
2. If you are unable to print from “send via Bluetooth,” select  
“connectivity” or “Bluetooth” under the “settings” or “tools”  
menu. Search for devices and select the Polaroid printer. Once  
paired, go back to stored images and select the image you  
want to print. In the “options” menu, select “beam” or “send via  
Bluetooth”. Select the Polaroid printer and print.  
Remove battery door cover.  
Install battery.  
Replace battery door cover.  
To charge the battery:  
1. Install the battery (see above steps).  
2. Connect the AC adapter to the printer and the power source.  
Notes:  
Before using the printer on battery power, fully charge the battery for  
2.5 hours.  
You can print photos while plugged into the power source.  
3. If your camera cell phone does not include “send via Bluetooth”  
under the “options” menu, select the image you want to print.  
Select the “options” menu and select “print via Bluetooth”.  
Search for devices, select the Polaroid printer, and print.  
Installing Polaroid ZINK Photo Paper™  
To install the Paper:  
Printing: Digital Camera  
For specific print directions for your digital camera, please review your digital  
camera user’s manual or manufacturer’s website.  
1
2
Press and release latch on the paper tray door.  
Unwrap the 10-pack of Polaroid ZINK  
Photo Paper.  
The following is an example for connecting to the printer and print your images.  
The terminology used in your camera may be different.  
3
4
1. Connect your digital camera and printer to determine if a print  
option or printer icon is automatically displayed on the camera  
screen.  
2. If no print option appears, select “menu” and navigate to  
confirm that PictBridge is enabled. Note: if “USB” is displayed  
under “settings” then PictBridge is NOT enabled.  
3. Once PictBridge is enabled, select the image you want to print  
and follow the on-screen instructions to print.  
Slide the 10-pack of Polaroid ZINK Photo  
Paper into the printer. Make sure the ZINK  
Smart Sheet™ is placed facedown. Close the  
printer tray door. The ZINK Smart Sheet will  
automatically eject.  
Press and hold the POWER button to turn  
on the printer.  
Notes:  
Do not disconnect the USB cord until entire printing process is  
complete.  
Do not turn off the printer while printing.  
Do not open paper tray door while printing.  
To print the date on your photo, ensure the Date Stamp feature on  
your digital camera is enabled.  
Notes:  
Works only with Polaroid PoGo™ and other Polaroid ZINK products.  
The printer must be empty before refilling. Do not fill the printer with more than one 10-pack of  
Polaroid ZINK Photo Paper. Having more than 10 sheets of paper may damage the printer.  
Aviod bending the Polaroid ZINK Photo Paper.  
Only hold the Polaroid ZINK Photo Paper by its edges; avoid touching the printing surface with  
your fingers.  
Does not print when connected to a PC.  
 

Peavey Stereo System Univerb User Manual
Philips Computer Drive PCRW404K 17 User Manual
Philips Digital Camera MIC4014SB User Manual
Philips DVD Player DVD724 User Manual
Philips Flat Panel Television 15PF 9925 User Manual
Philips Headphones SBCHJ055 User Manual
Philips Stereo System MME 100 User Manual
Philips Stereo System MX5500D User Manual
Porter Cable Portable Generator H1000IS W User Manual
Proctor Silex Oven 840160900 User Manual